How to install the bathtub How to install the bathtub

In the modern bathroom space, many people like to put a bathtub, so that we can lie down and take a comfortable bath after get off work. Do you know how the bathtub is installed? Today we are going to learn about the bathtub installation, hope it will be helpful to you.

The first step of the bathtub installation method: test whether the water leaks.

Before placing the bathtub, install the water fittings and close the water for 24 hours to see if there is any leakage in the bathtub. Pay special attention to the upper overflow. It is difficult to keep the water closed for 24 hours. Pour two buckets of water outside the bathroom and try to drain the water in the installed bathtub. This is more convenient for operation.

When it was actually installed, the bathtub was directly lifted into the bathroom and placed in the drain position. Because the mixing position of the faucet left when the water was changed is just the width of the bathtub, if the size of the bathtub is If the mixing water is not right, it is necessary to pay attention to the center point of the bathtub should be facing the center point of the mixing water, otherwise it will be ugly after the mixing faucet is installed in the future.

After the bathtub is lifted into the bathroom, start to install the water and water accessories, fill the bathtub with water, turn off the water, and check for leaks. When the water flows over the upper overflow, the water in the bathtub will flow from the overflow When I was out, I was lying on the ground and reaching under the bathtub to touch the back of the overflowing water to see if there was any water leaking from here.

After the overflow test passed, I then checked the tightness of the water. I chose to stand still and observe the tightness of the water. There was no problem at the beginning. After about 10 minutes, it was quiet. There was a gurgling sound of water bubbling in the bathroom every few seconds. The water was not installed and sealed, and there was leakage. I decided to drain the water and install it again. This time I found a problem. The copper drain pipe that was bubbling with blisters had a trachoma in a certain part. We tossed it several times and leaked it.

It’s a bit fortunate here. I carried the bathtub into the bathroom from the beginning. I was not afraid of wasting water during the water discharge experiment. It was also a full tank of water. Under pressure, the sand hole was compressed, so It will leak. If there is only a small amount of water and the pressure is not so high, it will not leak at this time. If you are a skilled hydraulic worker, you may be very impatient with my test. Maybe this problem will not be discovered at that time? On the other hand, it also proves from the side that the quality of the hardware is indeed average, and it is better to buy the hardware.

It should be noted that: whether the center point of the width of the bathtub is aligned with the center point of the faucet. This point must be considered when changing the water at the beginning. The width of the bathtub is 700*750*800. Once the water is changed and the size of the mixed water is determined, try to buy the bathtub according to this, otherwise change it later. The distance between the mixed water and the wall size is very difficult.

The second step of the bathtub installation method: leveling the bathtub.

When placing the bathtub, make sure that the other end of the drain is slightly higher than the end of the drain, so that the sewage will not be discharged smoothly in the future. This depends on the situation. Observing that the bottom of the bathtub originally had a drainage slope, the four sides of the bathtub were leveled with a spirit level and put in a water test. As expected, the water quickly drained. The bathtub visually maintains a horizontal and beautiful appearance without affecting the drainage effect.

The third step of the bathtub installation method: fill sand.

Although the cast iron bathtub is strong, its thermal conductivity is very fast. You should use medium river sand to lay down and smash the bottom of the bathtub firmly. Bricklayers also recommend using foam. Considering that foam is not as fluid as river sand, it is suitable to fill all gaps. In the process of filling river sand, how to prevent sand from leaking into the sewer is a problem to be solved.

After all the installation work is completed, the water will be tested again (this step is mainly to ensure that the moving bathtub does not cause the water to leak). After confirming that it is correct, wait for the bricklayer to build the skirt.

The fourth step of the bathtub installation method: leave the inspection port.

There is a hole with a height of 300 mm and a width of 400 mm at the drain. Cut a hole according to the size, and cut the board (thickness 40 mm) that has been water-proof and anti-corrosion treatment according to the size. The calculated value is calculated on the board. Count and Arrange the Bricks Use 903 construction glue to stick the bricks on the board. The edge of the protruding brick is smeared with sealant and inlaid on the box body, which is to facilitate the maintenance of the bathtub drainage system in the future. When building the bathtub skirt, for aesthetic considerations, all the height of 600 is reserved, and other materials such as mosaics are discarded. The bathtub skirt uses the same bricks as the lower part of the wall tiles. When this is done, the lower wall tiles, floor tiles, and bathtub skirts are all made of One color and one material are very beautiful.

The fifth step of the bathtub installation method: tiling.

The tiling of the bathtub skirt does not need to be scratched. Lay a red brick table, apply a layer of cement mortar on the surface, and then wait two days for tiling. The tiling is very troublesome. The ground has a slope, and the bathtub is flat, so each large brick must be polished to a different size. It cannot be polished a lot at a time. It is easy to polish and needs to be polished repeatedly. The upper fortress of the brick is tucked under the round edge of the bathtub so that it does not form a positive angle.

The above is the entire content of the bathtub installation. I hope it will be helpful to you. More decoration information is available on Qijia.com, so stay tuned.

More articles:

Will Faither Sanitary Ware recommend Faither Sanitary Ware

Which brand of shower room is the best shower room brand

Would you recommend Wrigley bathroom cabinets for Wrigley bathroom cabinets?

Which material is good for bathing wooden tubs? How to choose bathroom products?