Rifeng Sanitary Ware: What should I do if the toilet tank overflows?

Rifeng Sanitary Ware: What should I do if the toilet tank overflows? One of the common causes and solutions for leaking toilets is that the water tank is too full to overflow. There are many reasons for the overflow of the water tank. When we encounter this problem, how should we solve it? 1. The water inlet valve does not enter the water (1) Check whether the tap water pressure is too low. (2) Check whether the filter of the inlet valve is blocked by debris. (3) Open the water inlet valve cover and check whether the sealing ring in the water inlet valve body falls off or there are sundries such as hemp wire, iron filings, and sand. (4) Check whether the floating body of the inlet valve is stuck with the wall of the water tank, and whether the floating body can move up and down freely. 2. The water tank has been filled with water but the water inlet valve continues to feed water (1) Check whether the tap water pressure is too low (under 0.05Mpα) or too high (0.8Mpα). (2) Check whether the floating body of the inlet valve can move up and down freely, and whether it is jammed by the tank wall or other parts. (3) Open the water inlet valve and check whether the sealing rubber ring in the valve body is stuck by debris or falls off and shifts. (4) Check whether the inlet valve is broken. 3. Press the drain valve button or wrench, but the drain valve does not drain. Check whether the drain valve chain is off or is too long. 3. Press the drain valve button or wrench. Although the drain valve drains, it will stop draining after releasing it. (1) Check whether the drain valve chain is adjusted too short or too long. (2) Whether the leaking hole of the delay cup is too long. If it is because the toilet water level is too high, how should the toilet water level be adjusted? 1. How to adjust the water level of the toilet tank? There are screws in the water tank, and there is a pinch iron with a root iron. The middle iron piece pulls the iron upwards to lower it, and downwards it raises it. When you open the lid of the toilet, you can see the ball linkage mechanism inside. There is a screw, you can see that there is a screw on it, adjust it up to meet your requirements. Although the water level is low, it can save water! If you want the easiest way to save water, put one or two beer bottles filled with water in the water tank, one bottle can occupy about 700 ml of volume. 2. How to adjust the water fittings of the toilet (toilet) 1. Installation and adjustment of the water inlet valve (1) Installation of the water inlet valve: Take out the parts of the water inlet valve. Then install the adjusted inlet valve on the inlet hole of the water tank, put on the gasket, and tighten the fastening nut. (Note: The installation direction of the water inlet valve should ensure that the water supply pipe cannot be discounted or obstruct the work of other parts.) (2) Water volume adjustment of the water inlet valve tank: First turn the card of the water inlet valve to the 'OPEN' direction. Then pull the inlet valve body to raise or lower the inlet valve as a whole. The locking and loosening of the card refer to the identification of the water inlet pipe. (3) Inlet valve water tank water level fine-tuning adjustment: adjusting the adjustment lever can raise or lower the water tank water level. When the adjusting rod is rotated counterclockwise, the floating box will drop and the water level of the water tank will drop. On the contrary, rotating the adjusting rod clockwise will cause the floating box to rise and the water level of the water tank to rise. 2. Installation and adjustment of drain valve (1) Installation and disassembly of drain head. a. Rotate the valve body counterclockwise, and then take out the valve body upward; b. Loosen the fastening nut and take out the gasket. Then install the drain head on the drain hole of the water tank and adjust the proper position. Put on the gasket and tighten the fastening nut. c. Fasten the positioning buckle of the valve body to the positioning hole of the drain head. Then rotate the valve body clockwise. Once installed, it will be OK when you hear a 'click'. (2) The adjustment of the drain valve (small drain adjustment) The adjustment of the quilt cup can adjust the water volume of the small drain by moving up and down. The higher the position of the adjusting cup, the higher the water saving level, the smaller the water discharge. Conversely, the lower the position of the adjusting cup, the greater the displacement. (3) The adjustment of the drain valve (large drain adjustment) The adjustment section switch can make the drain valve large drain. When the adjustment switch moves down to seal the small hole, the water displacement is large. On the contrary, moving upwards will open the small holes, and the displacement will be small. (4) Adjustment of the button of the drain valve: Rotate the button of the valve body, which can be rotated 360° to correspond to the direction of the push rod of the button. Editor's summary: There may be many reasons for the overflow of the water tank, and the solutions may be different according to different reasons. Let's learn these common problems and solutions together!