< img height="1" width="1" style="display:none;" alt="" src="https://px.ads.linkedin.com/collect/?pid=5785916&fmt=gif" />
loading

KingKonree - Solid Surface Manufacturer of Sanitary Ware, Solid Surface Countertops & Sheets for over 24 years, innovation in moulding and thermoforming

 

Rifeng bathroom analysis shower room shower installation height and installation method

by:KingKonree     2021-09-13
Rifeng Sanitary Ware analyzes the installation height and installation method of the shower room showerhead. The showerhead is an essential tool for us to take a shower. If the installation is not suitable, it will not be comfortable to use. So today I want to explain the showerhead to everyone. The installation height and installation method are as follows. 1. The installation height of the shower head can be divided into two types according to the type of shower head: According to relevant regulations, the center of the concealed shower outlet should be 2.1 meters from the ground, and the center of the shower switch should be 1.1 meters from the ground. ;The surface-mounted boom shower is generally defined by the surface of the shower, and the best distance is 2 meters. It should be noted that these data are only average data, and the actual installation should be adjusted according to the height of the user. The concealed water pipe for the exposed shower switch is hot on the left and cold on the right. The center spacing should be 150cm. The concealed water outlet of the wall should be level with the tile surface, and the internal concealed water pipe should be perpendicular to the wall. After the shower is installed, it should be with the wall Face at a 90 degree angle. In addition, the water pressure adjustment is also a key point: under normal circumstances, the water pressure within 1.5 kg is the most suitable for the use of the shower. Excessive water pressure will cause the shower to be violent, and the small shower cannot be used normally. 2. How to install the shower head ① Screw the cover of the hot and cold water outlet of the shower head and install it into an S-type connector. The direction of this connector can be adjusted to facilitate the connection with the shower faucet. The joint should be wrapped with raw tape, the number of turns should not be less than 30 turns, to prevent the water pipe from leaking. ②Before installing the shower faucet, the filter must be installed first. The filter screen can filter the sand and gravel brought by the water flow. Although it may be blocked, it protects the most important part of the faucet-the valve core from the friction of the sand and gravel. ③Use a spirit level to measure whether the faucet is installed horizontally, and then install the shower rod and nozzles. 3. Owner's acceptance method: Shake the shower rod to check whether it is firm, whether the switch is smoothly switched, and check whether the water pipe is leaking. 4. Data for shower installation. The best distance from the faucet of the shower to the ground is 1 meter. The height of the shower head of the lifting pole is preferably 2 meters, this distance is just enough to allow the water to cover the whole body, and the intensity of the water flow is appropriate. The installation height of the mobile shower handle is usually 1.7 meters, and it needs to be adjusted according to the height of the user. The most suitable distance is for a person to stand on the ground and reach out to get the shower handle, otherwise it is too high to hold the shower head. It is easy to stand unstable and cause safety accidents. 5. Some details that should be paid attention to during the installation of the shower 1. The shower should be installed according to the actual needs of the owner: When determining the installation height of the shower, the installer will determine the most suitable height according to the owner's on-site trial situation, so as to facilitate the owner in the future usage of. 2. Use cloth to protect the faucet: When tightening the faucet, a careful person will wrap the screw cap of the faucet with a thicker cloth or plastic film to prevent the faucet from being messed up by the wrench. 3. Clean up site dust after installation: some dust and other dust will inevitably be generated during the installation process, which should be cleaned up after the installation work is completed to ensure that the site is clean and can be rinsed with water. (
Custom message
暂无友情链接数据
Chat Online 编辑模式下无法使用
Leave Your Message inputting...